Tennant 8200D Operator'S Manual Download Page 85

Page: 85 / 102

MAINTENANCE

8200D 330080 (12--00)

ADJUSTING REAR SQUEEGEE BLADE

DEFLECTION
Deflection is the amount of curl the squeegee

blade has when the machine moves forward with

the squeegee lowered to the floor.

1. Lower the squeegee and drive the machine

forward.

2. Shut off the engine and set the machine

parking brake.

FOR SAFETY: Before leaving or

servicing machine; stop on level

surface, set parking brake, turn off

machine and remove key.

3. Look at the deflection of the rear squeegee

blade. The correct amount of deflection is 25

to 22 mm (1.00 to 0.88 in) at the center of

the squeegee and about 3 mm (0.12 in) less

deflection at the tips of the squeegee.

4. To adjust the amount of deflection, loosen

the top knob on the two casters.

5. Turn the bottom knob clockwise to decrease

the blade deflection. Turn the bottom knob

counter-clockwise to increase the blade

deflection. Be sure to turn both knobs the

same

number of turns. Tighten the top

knobs on the casters.

6. Start the machine, lower the squeegee and

drive the machine forward again to check

the squeegee blade deflection. Readjust the

squeegee blade deflection if necessary.

7. Raise the squeegee when finished.

03719

25 to 22 mm

1.00 to 0.88 in

Summary of Contents for 8200D







































































































Search results

Summary of Contents for 8200D

Reviews:

Related manuals for 8200D

Brands by name

Popular brands

Tennant 8200D, Operator'S Manual

Search results

Summary of Contents for 8200D

Reviews:

Related manuals for 8200D

Brands by name

Popular brands