Tennant 8200D Operator'S Manual Download

Page: 94 / 102

MAINTENANCE

8200D 330080 (12--00)

6. Set the parking brake, lower the scrub head

and block the machine tires. Tie down the

machine to the truck or trailer before

transporting.

The front tie-down locations are the holes in

the wheel pockets at the front of the

machine frame.

The rear tie-down locations are the bottom

lips at each corner of the rear bumper.

7. If the loading surface is not horizontal or is

higher than 380 mm (15 in) from the ground,

use a winch to unload machine.

If the loading surface is horizontal AND is

380 mm (15 in) or less from the ground, the

machine may be driven off the truck or

trailer.

FOR SAFETY: When unloading machine

off truck or trailer, use winch. Do not

drive the machine off the truck or trailer

unless the loading surface is horizontal

AND 380 mm (15 in) or less from the

ground.

Summary of Contents for 8200D







































































































Search results

Summary of Contents for 8200D

Reviews:

Related manuals for 8200D

Brands by name

Popular brands

Tennant 8200D, Operator'S Manual

Search results

Summary of Contents for 8200D

Reviews:

Related manuals for 8200D

Brands by name

Popular brands