Tennant 8200D Operator'S Manual Download Page 88

Page: 88 / 102

MAINTENANCE

8200D 330080 (1--98)

SKIRTS AND SEALS

REAR SKIRTS

The two rear skirts are located on the bottom rear

of the main brush compartment. The vertical skirt

(rear) should clear the floor up to 3 mm (0.12 in)

in dusty conditions, and touch the floor otherwise.

Check the skirts for wear or damage and

adjustment daily.

BRUSH DOOR SEALS

The brush door seals are located on the main

brush door and on corresponding portions of the

main frame.

Check the seals for wear or damage every

100 hours of operation.

HOPPER LIP SKIRTS

The hopper lip skirts are located on the bottom

rear of the hopper. The skirts float over debris and

help deflect that debris into the hopper. The

hopper lip skirts consist of five bottom lip

segments and two additional side lip segments.

Check the hopper lip skirts for wear or damage

daily.

Replace the hopper lip skirts when they no longer

touch the floor.

Summary of Contents for 8200D







































































































Search results

Summary of Contents for 8200D

Reviews:

Related manuals for 8200D

Brands by name

Popular brands

Tennant 8200D, Operator'S Manual

Search results

Summary of Contents for 8200D

Reviews:

Related manuals for 8200D

Brands by name

Popular brands