Tennant 8200D Operator'S Manual Download Page 24

Page: 24 / 102

OPERATION

8200D 330080 (1--98)

SWEEPING VACUUM FAN SWITCH

The sweep vacuum fan switch starts and stops

the sweep vacuum fan. Do not operate the

vacuum fan when sweeping in wet conditions.

Start: Press the switch. The indicator next to the

switch will illuminate.

Stop: Press the switch. The indicator light next to

the switch will go out.

NOTE: The sweep vacuum fan activates

automatically when the main sweeping brush

starts operating. The sweep vacuum fan will not

activate unless the main sweeping brush is

operating.

NOTE: The sweep vacuum fan will not start if the

hopper is raised, even slightly. If the sweep

vacuum fan switch is pressed while the hopper is

raised, the sweep vacuum will not start.

FILTER SHAKER SWITCH

The filter shaker switch starts the hopper dust

filter shaker. The shaker automatically operates

for 30 seconds.

Start: Press the filter shaker switch. The indicator

light will remain on while the filter shaker is

operating.

NOTE: The filter shaker will activate automatically

for a short time each time the sweeping

operations are stopped. The filter shaker will not

operate while the sweeping or vacuum system is

operating.

Summary of Contents for 8200D







































































































Search results

Summary of Contents for 8200D

Reviews:

Related manuals for 8200D

Brands by name

Popular brands

Tennant 8200D, Operator'S Manual

Search results

Summary of Contents for 8200D

Reviews:

Related manuals for 8200D

Brands by name

Popular brands