Tennant 8200D Operator'S Manual Download Page 28

Page: 28 / 102

OPERATION

8200D 330080 (6--04)

HOPPER TEMPERATURE LIGHT --

THERMO SENTRY

The hopper temperature light will illuminate when

there is too much heat, possibly from a fire, in the

hopper. The Thermo Sentry will stop the sweeping

vacuum fan. If the light illuminates stop the

machine immediately, then find the problem and

have it corrected.

OK LIGHT

Each time the key switch is turned to the on

position the instrument panel will run a

self--diagnostic test. If the instrument panel

passes the test, the OK light will illuminate.

CLOGGED FILTER LIGHT (OPTION)

The clogged filter light will illuminate when the

hopper dust filter is clogged.

To clean the filter, press the filter shaker switch. If

the clogged filter light remains lit, manually clean

the hopper dust filter. See

HOPPER DUST

FILTER

in the

MAINTENANCE

section of this

manual

Summary of Contents for 8200D







































































































Search results

Summary of Contents for 8200D

Reviews:

Related manuals for 8200D

Brands by name

Popular brands

Tennant 8200D, Operator'S Manual

Search results

Summary of Contents for 8200D

Reviews:

Related manuals for 8200D

Brands by name

Popular brands