Tennant 8200D Operator'S Manual Download

Page: 19 / 102

OPERATION

8200D 330080 (6--04)

HOPPER DOOR LEVER

The hopper door lever opens and closes the

hopper door.

Hopper door close: Pull and hold the hopper door

lever backward for approximately four seconds or

until the hopper door closed light (option) on the

dashboard illuminates.

Hopper door open: Push the hopper door lever

forward to the detent position.

CONTROL PANEL

The control panel controls all scrubbing

operations and the sweeping vacuum fan and

filter shaker motor.

HOURMETER

The hourmeter records the number of hours the

machine has been operated. Check the hourmeter

regularly; this information is used to determine

when to perform routine machine maintenance.

FUEL LEVEL GAUGE

The fuel level gauge indicates the amount of fuel

remaining in the fuel tank. As the fuel is

consumed, the indicator lights will move across

the display from right to left. When only the light

on the far left is lit, the fuel tank is nearly empty.

Refill the fuel tank as soon as possible.

Summary of Contents for 8200D







































































































Search results

Summary of Contents for 8200D

Reviews:

Related manuals for 8200D

Brands by name

Popular brands

Tennant 8200D, Operator'S Manual

Search results

Summary of Contents for 8200D

Reviews:

Related manuals for 8200D

Brands by name

Popular brands