Tennant 8200D Operator'S Manual Download Page 57

Page: 57 / 102

OPERATION

8200D 330080 (1--98)

OPERATION ON INCLINES

Drive the machine slowly on inclines. Use the

brake pedal to control machine speed on

descending inclines. DO NOT turn the machine

on an incline; drive straight up or down.

The maximum rated incline for sweeping and

scrubbing with the machine is 6

. The maximum

rated incline during transport of the machine is 8

FOR SAFETY: When using machine, go

slow on inclines and slippery surfaces.

TIE DOWNS

The machine can be tied down for transport using

the tie-down holes at the front and rear of the

machine.

The front tie-down holes are located in front of the

front tires.

The rear tie-downs are located on the rear

corners of the machine.

When transporting the machine on a trailer or in a

truck, be sure to set the parking brake and block

the tires to prevent the machine from rolling.

Summary of Contents for 8200D







































































































Search results

Summary of Contents for 8200D

Reviews:

Related manuals for 8200D

Brands by name

Popular brands

Tennant 8200D, Operator'S Manual

Search results

Summary of Contents for 8200D

Reviews:

Related manuals for 8200D

Brands by name

Popular brands