Tennant 6100E Service Manual Download

Page: 148 / 228

ELECTRICAL

4--6

6100E 330255 (6--01)

4. Check the water level in all the battery cells.

5. If the level is low, add just enough distilled

water to cover the battery plates. DO NOT

OVERFILL. The batteries can overflow

during charging due to expansion.

NOTE: Make sure the battery caps are in place

while charging.

FOR SAFETY: When maintaining or

servicing machine, avoid contact with

battery acid.

6. Unplug the battery connector from the

machine connector.

7. Plug the connector from the batteries into

the battery charger connector.

WARNING: Batteries emit hydrogen gas.

Explosion or fire can result. Keep

sparks and open flame away. Keep

covers open when charging.

NOTE: Plug the charger connector into connector

that runs to the batteries. Do not plug charger into

mounted connector. Damage may occur to the

machine.

Summary of Contents for 6100E





































































































































































































































Search results

Summary of Contents for 6100E

Reviews:

Related manuals for 6100E

Brands by name

Popular brands

Tennant 6100E, Service Manual

Search results

Summary of Contents for 6100E

Reviews:

Related manuals for 6100E

Brands by name

Popular brands