TeleWell TW-EF600 User Manual Download

Page: 9 / 133

Hardware Specifications

Physical Interface

Please refer to the instructions on the label of the outer box to get the specification of your device.

Optical SC-connector with options:

- 100BASE-LX dual fiber single-mode WAN (Tx/Rx1310nm)

- 100BASE-BX single-strand single-mode WAN (Tx1310nm/Rx1550nm)

- 100BASE-FX dual fiber multimode WAN (Tx/Rx1310nm)

- 1000BASE-LX dual fiber single-mode WAN (Tx/Rx1310nm)

- 1000BASE-BX single-strand single-mode WAN (Tx1310nm/Rx1490nm)

100/1000BASE Optical SFP Optical convector

WLAN: 3 x detachable antennae (802.11n Fiber Optical Router only)

Ethernet: 4-port 10/100/1000M auto-crossover (MDI / MDI-X) Switch

Factory default reset button

WPS push button (802.11n Fiber Optical Router only)

Power jack

Power switch

Operating Environment

Operating temperature: 0

– 40°C

Storage temperature: -20

– 70°C

Humidity: 20

– 95% non-condensing

Summary of Contents for TW-EF600






































































































































Search results

Summary of Contents for TW-EF600

Reviews:

Related manuals for TW-EF600

Brands by name

Popular brands

TeleWell TW-EF600, User Manual

Search results

Summary of Contents for TW-EF600

Reviews:

Related manuals for TW-EF600

Brands by name

Popular brands