background image

9600 SERIES VOIP USER GUIDE: CETIS SIP 2017   

www.telematrix.net

 

27

This equipment has been tested and found to 
comply with the limits for a Class B digital device, 
pursuant to Part 15 of the FCC Rules . These limits 
are designed to provide reasonable protection 
against harmful interference in a residential 
installation . This equipment generates, uses, 
and can radiate radio frequency energy and, if 
not installed and used in accordance with the 
instructions, may cause harmful interference 
to radio communications . However, there is no 
guarantee that interference will not occur in a 
particular installation .

If this equipment does cause harmful interference 
to radio or television reception, which can be 
determined by turning the equipment off and on, the 
user is encouraged to try to correct the interference 
by one or more of the following measures: 

–  Reorient or relocate the receiving antenna 

for the radio or television that is receiving the 
interference) . 

–  Reorient or relocate and increase the 

separation between the telecommunications 
equipment and receiving antenna . 

–  Connect the telecommunications equipment 

into an outlet on a circuit different from that to 
which the receiving antenna is connected . 

FCC RF Radiation Exposure 

Statement

The installation of the base unit should allow 
at least 20 centimeters between the base 
and persons to be in compliance with FCC RF 
exposure guidelines . For body-worn operation, 
the portable part (handset) has been tested and 
meets FCC RF exposure guidelines .

This device must not be co-located or operating 
in conjunction with any other antenna or 
transmitter . The changes or modifications not 
expressly approved by the party responsible for 
compliance could void the user’s authority to 
operate the equipment . 

Industry of Canada Requirements

Note: This equipment meets the applicable 
Industry Canada Terminal Equipment Technical 
Specifications . This is confirmed by the 
registration number . The abbreviation, IC, before 
the registration number signifies that registration 
was performed based on a Declaration of 
Conformity indicating that Industry Canada 
technical specifications were met . It does not imply 
that Industry Canada approved the equipment .

Before installing this equipment, users should 
ensure that it is permissible to be connected to 
the facilities of the local telecommunications 
company . The equipment must also be installed 
using an acceptable method of connection . The 
customer should be aware that compliance with 
the above conditions may not prevent degradation 
of service in some situations .

Repairs to certified equipment should be 
coordinated by a representative designated by the 
supplier . Any repairs or alterations made by a user 
to this equipment, or equipment malfunctions, 
may give the telephone communications company 
cause to request the user to disconnect the 
equipment .

Users should ensure for their own protection, that 
the electrical ground connections of the power 
utility, telephone lines, and internal metallic 
water pipe system, if present, are connected 
together . This precaution may be particularly 
important in rural areas . 
Caution: Users should not attempt to make such 
connections themselves, but should contact 
the appropriate electric inspection authority, or 
electrician, as appropriate .
Notice: The Ringer Equivalence Number (REN) 
assigned to each terminal device provides an 
indication of the maximum number of terminals 
allowed to be connected to a telephone interface . 
The termination on an interface may consist 

Summary of Contents for MARQUIS 9600 Series































Reviews: