manualshive.com logo in svg

Teledyne Princeton Instruments IsoPlane 81, Manual

Share
Download
Teledyne Princeton Instruments IsoPlane 81 Manual Download Page 4

4

IsoPlane

®

 81 Imaging Spectrometer System Manual

 Issue 1

C.1

Grating Carrier Replacement Procedure  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41

C.2

Grating Carrier Alignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  46
C.2.1

Grating Carrier Adjustment Screws. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  46

C.2.2

Grating Carrier Alignment Procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . .47

C.3

Replace Grating Housing Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  49

C.4

Final Alignment  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Appendix D: Internal Shutter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

D.1

Required Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

D.2

Internal Shutter Removal Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

D.3

Internal Shutter Installation Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52

Appendix E: Timing Generator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

E.1

T

0  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

E.2

Configuring the Timing Generator in LightField . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
E.2.1

Repetitive Timing Mode  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53

E.2.2

Sequential Timing Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  54

E.3

Clarification of Gate Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55

Warranty and Service. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Limited Warranty  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57

Basic Limited One (1) Year Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
Limited One (1) Year Warranty on Refurbished or Discontinued Products  . . .57
XP Vacuum Chamber Limited Lifetime Warranty . . . . . . . . . . . . . . . . . . . . . . . . .57
Sealed Chamber Integrity Limited 12 Month Warranty . . . . . . . . . . . . . . . . . . .  58
Vacuum Integrity Limited 12 Month Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . .  58
Image Intensifier Detector Limited One Year Warranty. . . . . . . . . . . . . . . . . . .  58
X-Ray Detector Limited One Year Warranty  . . . . . . . . . . . . . . . . . . . . . . . . . . . .  58
Software Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  58
Owner's Manual and Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  59
Your Responsibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  59

Contact Information  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  60

Summary of Contents for Princeton Instruments IsoPlane 81































































Reviews:

No comments

Brands by name

Popular brands

Load more brands