Teledyne Princeton Instruments IsoPlane 81 Manual Download Page 46

Page: 46 / 62

IsoPlane

81 Imaging Spectrometer System Manual

Issue 1

14. Now that a new Grating Carrier has been installed, it must be aligned. Proceed to

Section C.2.

C.2

Grating Carrier Alignment

This section provides information necessary to align an IsoPlane 81 Grating Carrier.

The following tools are required to align an IsoPlane 81 Grating Carrier:

•

0.05” Allen wrench

•

5/64” Allen wrench

•

3/32” Allen wrench

•

1/8” nut driver

C.2.1

Grating Carrier Adjustment Screws

Figure C-11 shows the locations of all adjustment screws required to align an IsoPlane
81 Grating Carrier.

Figure C-11: Grating Carrier Adjustment Screws

Refer to Table C-1 for information about each adjustment screw, listed alphabetically by
label/identifier.

Table C-1:

Grating Adjustment Screw

Label/Identifier

Adjustment/Purpose

Adjustment Tool

Tilt adjustment.

0.05” Allen wrench

Tangent adjustment.

5/64” Allen wrench

L11

Tilt adjustment, initial lock.

3/32” Allen wrench

L12

Tangent adjustment, initial lock.

1/8” nut driver

L21

Tilt adjustment, final lock.

3/32” Allen wrench

L22

Tangent adjustment, final lock.

1/8” nut driver

Summary of Contents for Princeton Instruments IsoPlane 81































































Search results

Summary of Contents for Princeton Instruments IsoPlane 81

Reviews:

Brands by name

Popular brands

Teledyne Princeton Instruments IsoPlane 81, Manual

Search results

Summary of Contents for Princeton Instruments IsoPlane 81

Reviews:

Brands by name

Popular brands