Teledyne Princeton Instruments IsoPlane 81 Manual Download Page 60 | Manualshive

Page: 60 / 62

background image

60

IsoPlane

®

81 Imaging Spectrometer System Manual

Issue 1

below the waterline, heavy lift operations, or the transportation to or from offshore
locations.

10. After the warranty period has expired, you may contact the Teledyne Princeton

Instruments factory or a Teledyne Princeton Instruments authorized representative for
repair information and/or extended warranty plans.

11. Physically damaged units or units that have been modified are not acceptable for

repair in or out of warranty and will be returned as received.

12. THESE EXPRESS WARRANTIES, INCLUDING THE REMEDIES SET FORTH HEREIN, ARE

EXCLUSIVE AND ARE IN LIEU OF ANY AND ALL OTHER WARRANTIES, EXPRESS OR
IMPLIED. NO WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE IS INTENDED OR GIVEN. IN THE CASE OF GOODS OTHER THAN THOSE OF
SELLER’S OWN MANUFACTURE, SELLER MAKES NO WARRANTIES, EXPRESS,
STATUTORY, OR IMPLIED.

13. When contacting us for technical support or service assistance, please refer to the

Teledyne Princeton Instruments factory of purchase, contact your authorized
Teledyne Princeton Instruments representative or reseller, or visit our technical
support page at

www.princetoninstruments.com

.

Contact Information

Teledyne Princeton Instruments’ manufacturing facility for this product is located at the
following address:

Teledyne Princeton Instruments
3660 Quakerbridge Road
Trenton, NJ 08619 (USA)

Tel: 1-800-874-9789 / 1-609-587-9797
Fax: 1-609-587-1970

Customer Support E-mail:

[email protected]

Refer to

http://www.princetoninstruments.com/support

for complete support and

contact information, including:

•

Up-to-date addresses and telephone numbers;

•

Software downloads;

•

Product manuals;

•

Support topics for Teledyne Princeton Instruments’ product lines.

«
...
58
59
60
61
62
»

Summary of Contents for Princeton Instruments IsoPlane 81































































Reviews:

No comments

Related manuals for Princeton Instruments IsoPlane 81

Brand: Waterwise Pages: 12

Brand: ParaBody Pages: 38

Brand: Balanced Body Pages: 4

Brand: GE Pages: 802

Brand: iET Pages: 17

Brand: Tacx Pages: 2

Brand: C.E. Nierhoff & Co Pages: 7

DVCPRO P2 Series

Brand: Panasonic Pages: 32

Brand: A.MENARINI Pages: 2

Brand: B&K Pages: 16

Brand: B&G Pages: 2

Brand: Ebyte Pages: 7

Brand: Garmin Pages: 41

Brand: Landoll Pages: 144

Brand: Castellini Pages: 299

Brand: Lowenstein Medical Pages: 457

GrainLogix XLB10

Brand: LOFTNESS Pages: 104

INTRA PROPHYwiz 181 P

Brand: KaVo Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands