Teledyne Princeton Instruments IsoPlane 81 Manual Download Page 26 | Manualshive

Page: 26 / 62

background image

26

IsoPlane

®

81 Imaging Spectrometer System Manual

Issue 1

Figure 4-7:

Securing the Focusing CUBE

3.

Push the slit rightward to expose the full entrance aperture.

4.

Within LightField, from the Readout expander, select Full Frame from the Mode
pull-down list. See Figure 4-8.

Figure 4-8:

Configure Readout Mode

5.

From the Region of Interest expander, set ROI to Full Sensor.

6.

Point the IsoPlane 81 at an object that is more than 3 m (9.8 feet) away.

7.

On the Spectrometer expander, set the grating to 0 nm, click

and adjust

the focusing screw until the image comes into best focus.

NOTE:

The horizontal lens alignment screw may require
adjustment as well. However, this adjustment should only
be performed following the installation of all remaining
CUBES and/or fore optics.

«
...
24
25
26
27
28
...
»

Summary of Contents for Princeton Instruments IsoPlane 81































































Reviews:

No comments

Related manuals for Princeton Instruments IsoPlane 81

Brand: Waterwise Pages: 12

Brand: ParaBody Pages: 38

Brand: OfiTE Pages: 21

Brand: Earthlite Pages: 4

Brand: YATEK Pages: 78

Brand: LANGER EMV-Technik Pages: 25

Electric Clamshell CSE12-208VCD

Brand: Lang Pages: 16

Brillion 3631-25

Brand: Landoll Pages: 138

Brand: PASCO Pages: 5

Brand: Pasco Scientific Pages: 27

Brand: PARUS Pages: 6

Brand: Safavieh Pages: 2

Brand: Vendlet Pages: 2

Brand: Tar River Pages: 44

Brand: Tar River Pages: 61

Brand: Garden Treasures Pages: 2

Littmann Classic II Pediatric

Brand: 3M Pages: 53

Brand: RAMVAC Pages: 53

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands