Teledyne 2105 Installation And Operation Manual Download Page 66

Page: 66 / 98

2105 Interface Module
Section 3 Modbus Protocol and 2100 Output

3-8

280,281

Analog channel 8

4-byte float

0-100 percent

Read

282

Analog channel 8 status code

16-bit integer

Read

283-288

Analog channel 8 time record

Time

Read

Note

The following 21 parameters and register numbers pertain to the 2105 only, representing all

possible sonde measurements depending on the type of sonde(s) connected.

415,416

Concentration

4-byte float

TBD

Read

417

Concentration status code

16-bit integer

Read

418-423

Concentration time record

Time

Read

475,476

Fluorescence

4-byte float

Read

477

Fluorescence status code

16-bit integer

Read

478-483

Fluorescence time record

Time

Read

535,536

Battery

4-byte float

Volts

Read

537

Battery status code

16-bit integer

Read

538-543

Battery time record

Time

Read

595,596

Dissolved Gas

4-byte float

mmHg

Read

597

Dissolved Gas status code

16-bit integer

Read

598-603

Dissolved Gas time record

Time

Read

655,656

Circulator

4-byte float

TBD

Read

657

Circulator status code

16-bit integer

Read

658-663

Circulator time record

Time

Read

715,716

Photosynthetic Radiation

4-byte float

umol s

Read

717

Photosynthetic Radiation

status code

16-bit integer

Read

718-723

Photosynthetic Radiation

time record

Time

Read

775,776

Transmissivity

4-byte float

Read

777

Transmissivity status code

16-bit integer

Read

778-783

Transmissivity time record

Time

Read

835,836

Conductivity

4-byte float

uS/cm

Read

837

Conductivity status code

16-bit integer

Read

838-843

Conductivity time record

Time

Read

895,896

Specific Conductance

4-byte float

uS/cm

Read

897

Specific Conductance

status code

16-bit integer

Read

898-903

Specific Conductance

time record

Time

Read

Table 3-2 Modbus ASCII Address 2 +(N - 1) Register Definitions (Continued)

Register Number(s)

Name

Data Type

Units

Read/Write

Summary of Contents for 2105


































































































Search results

Summary of Contents for 2105

Reviews:

Teledyne 2105, Installation And Operation Manual, Page: 66 / 98

Search results

Summary of Contents for 2105

Reviews: