manualshive.com logo in svg

Teledyne 2105, Installation And Operation Manual, Page: 56 / 98

Share
Download
Teledyne 2105 Installation And Operation Manual Download Page 56

2105 Interface Module
Section 2 Installation and Operation

2-38

2.16 2105 Universal Cable

60-2004-580

This multipurpose cable connects to the 12-pin female connector
on the side of the 2105 module. The non-terminated end can be
wired to compatible circuits for interfacing. These instructions
explain how to prepare the cable for use, and the function of each
wire.

CAUTION

Risk of equipment damage. Only experienced electronic tech-
nicians should make the connections to an external device
using cable 69-2004-580.

2.16.1 Preparation

1. Referring to Table 2-4, select the appropriate wires and tin

the ends with solder or attach crimped connector ends.

2. Electrically insulate any unused wires.

3. Ensure that the connection has protection from the envi-

ronment, such as cable conduit. Teledyne Isco offers a
sealed, in-line cable joiner for water protection.

WARNING

Ensure that no wire ends come into contact with each other.

Personal injury, power shutdown, or component failure can
result. Wires not in use should be individually sealed at all
times.

2.16.2 2105 Connection

To connect the cable to a 2105 module, simply press the cable

connector into the module’s connector port until it clicks (Figure
2-36). To disconnect the cable, press down on the spring-loaded
connector tab and pull the cable connector out.

Note

Always insert connector caps into unused connectors to termi-
nate the network and prevent moisture damage.

Figure 2-36 2105 Interface connector

Module Connector
Tab

Universal Cable
Connector

(Modem
Module Shown)

Summary of Contents for 2105



































































































Reviews:

No comments