Teledyne 2105 Installation And Operation Manual Download Page 24

Page: 24 / 98

2105 Interface Module
Section 2 Installation and Operation

2-6

2.2.3 Installing the Batteries

The 2191 battery module requires two lantern batteries. The

figures below show a 6 VDC alkaline battery. Rechargeable 6

VDC lead-acid batteries are also available from Teledyne Isco.

To install the batteries, follow the instructions below.

Figure 2-6 Loading the 2191 Battery module

Note

The batteries should always be replaced as a pair. Never mix

old and new batteries.

1. Load the lantern battery into the

carrier.

2. Insert the carrier and battery into the module.

Note the position of the carrier’s connector; it
must be aligned toward the center of the module.

3. Align the marks indicated and

insert the door.

4. Rotate the door

turn clockwise.

Repeat this procedure to install
the second battery.

Summary of Contents for 2105


































































































Search results

Summary of Contents for 2105

Reviews:

Teledyne 2105, Installation And Operation Manual, Page: 24 / 98

Search results

Summary of Contents for 2105

Reviews: