Teledyne 2105 Installation And Operation Manual Download Page 12

Page: 12 / 98

2105 Interface Module
Section 1 Introduction

1-2

1.2 2105 Module

Components

Figures 1-1 and 1-2 identify the key components of the 2105
Interface Module.

Figure 1-1 2105 Components - Top View

2105 Module

2105

i Modem Module

Table 1-1 2105 Interface Module Components - Top View

Item No.

Name

Description

Communication Connector

This port is used to connect the 2105 to other modules in a stack,

or to a computer using an RS232 cable.

Connector Cap

Install on the communication connector when it is not in use to
protect the connector from moisture damage. When the connector
is in use, store the connector cap on the cap holder.

Cap Holder

Stores the connector cap when the communication connector is in
use.

Instrument Interface
Cable Connector

Used to connect the module to compatible equipment for data
logging and sampler control

Connector Plug

Insert into the interface connector when the connector is not in
use to protect it from damage.

Antenna Cable Connector
(2105

only)

Used to connect the modem to the magnetic mount antenna.

Connector Plug
(2105

only)

Insert into the antenna cable connector when the connector is not
in use to protect it from damage.

Latch Release

Push in to unlock the module from a stack.

Summary of Contents for 2105


































































































Search results

Summary of Contents for 2105

Reviews:

Teledyne 2105, Installation And Operation Manual, Page: 12 / 98

Search results

Summary of Contents for 2105

Reviews: