Teledyne 2105 Installation And Operation Manual Download Page 47

Page: 47 / 98

2105 Interface Module

Section 2 Installation and Operation

2-29

2.14 Modbus Input

The 2105 module is capable of receiving data from devices using

Modbus ASCII or Modbus RTU protocol.

The 2105 Modbus input function supports ASCII and RTU pro-

tocols, but the RS-232 can only interface directly with one input.

The RS-485 will require a converter, but it can support up to two

inputs. Teledyne Isco offers an RS-232 to RS-485 converter.

Note

You must set up and configure your monitoring/control system

and Modbus device(s)

before

adding the 2105 module.

Note

Modbus and Pulse Doppler input (see Section 2.13) cannot be
used simultaneously in the same system.

From the Modbus tab, configure the protocol. To add a device to
the system, click New Device.

Figure 2-32 Modbus input tab

Add Modbus
device

Summary of Contents for 2105


































































































Search results

Summary of Contents for 2105

Reviews:

Teledyne 2105, Installation And Operation Manual, Page: 47 / 98

Search results

Summary of Contents for 2105

Reviews: