manualshive.com logo in svg

Telect LTX, Install Manual

Share
Download
Telect LTX Install Manual Download Page 7

© Telect, Inc.  All rights reserved. 148326 09.08.16
1.509.926.6000  ::  telect.com

7

LTX Patch and Splice Panel

LTX Patch and Splice Panel

Fiber :: Install guide

Telect's LTX Patch and Splice Panel consolidates network fi ber 
splice, patching, and routing requirements in a 4RU panel. The 
LTX panel accommodates

•  

Up to 288 fiber terminations

•  

Stacked splice trays, each housing 36 splice sleeve 
holders

•  

Velcro bands that secure trays inside the panel

•  

Routing spools to manage slack cable routing

•  

Panel mounted cable clamp for incoming cable control

•  

Convenient spring-hinged removable front and rear doors 

•  

Designation labels on front and rear doors

Interconnect and cross-connect cabling enter the LTX panel at rear 
corner locations guided over rubber edge protectors. Slack storage 
area in the rear of the panel routes IntraFacility Fibers (IF) through 
the panel to splice trays in the center of the panel.  After splicing, 
pigtail fi bers connect to patch plate mounted connectors at the rear 
of the panel and fi ber jumpers connect to adapters at the front. 

LTX Patch and Splice Panel patch plates can accommodate:

•  

SC/UPC, SC/APC, LC/APC, LC/UPC are available in patch 
plates with 6 or 8 adapters

•  

LC/SC available in patch plates with 12 adapters

•  

LC/UPC and LC/APC available in patch plates with 24 
adapters

•  

MPO/MTP feed through patch plates available with 6 or 8 
adapters

 

In addition,Telect offers a special factory-confi gured integrated 
4RU patch plate panel with up to 288 terminations (requires use of 
LC duplex adapters).

Adapters are also offered in multimode versions. All adapters 
include dust covers. Most patch plates are available in white or 
black.

1.4  LTX Panel Overview

Figure 1-2 - LTX Patch and Splice Panel Overview

        - Front and Rear Views

LTX Patch and Splice Panel, Front View

(

144 terminations shown

)

Front Door

Rear Door

Routing Spool

Slack 

Storage 

Area

Fiber 

Jumper 

Entry

Area

Designation Card

(Front Side)

Patch Plate with Adapters

Cable 

Clamp

Designation Card

(Rear Side)

Cable 

Clamp

Arc

Patch 

Plate with 

Connectors

Arc

LTX Patch and Splice Panel, Rear View

(

144 terminations shown

)

Arc

Arc

Arc

Fiber 

Jumper 

Entry 

Area

Arc

Arc

Arc

Cable

Entry 

Area

Arc

Stacked 

Splice 

Trays

Cable

Entry 

Area

Arc

Velcro 

Tie

Summary of Contents for LTX



























Reviews:

No comments

Brands by name

Popular brands

Load more brands