manualshive.com logo in svg

Telect LTX, Install Manual

Share
Download
Telect LTX Install Manual Download Page 20

© Telect, Inc.  All rights reserved. 148326 09.08.16 v2
1.509.926.6000  ::  telect.com

20

LTX Patch and Splice Panel

LTX Patch and Splice Panel

Fiber :: Install guide

4.1.5   Install Pigtail Fiber Connectors

Refer to 

Figures 4-4 

and

 

4-5

 for this procedure.

Pigtail fi bers connect to connectors that plug in to the back of the 
patch panel in the rear of the LTX panel.  

1. 

Locate connector designation number on the designation 
card that is located on the LTX panel door. Record fi ber 
information.

2. 

Plug in connector with attached pigtail fi ber at designated 
connector location and run pigtail fi ber to the splice tray.

3. Proceed 

to 

Section 4.1.6, 

Route Pigtail FIbers in the Splice 

Tray

 before installing the next pigtail fi ber connector. 

NOTE:  Each splice tray contains sleeve holder slots for 36  
pigtail fi bers.

Figure 4-5 - Route Pigtail Fibers from Connectors

Connector 

Locations

Connect 

Pigtail 
Fibers

Route 

Pigtail 

Fibers to 

Splice Tray

Designation 

Card

Designation 

Card

LTX Panel Top View

Front

Rear

Splice Tray

LTX Panel Rear View

Designation 

Card

Mounting 

Bracket

Mounting 

Bracket

Splice 

Tray

Door

Connectors

Connect Pigtail Fibers

Front

Door

Rear

Door

Figure 4-4 - Pigtail Fiber Connectors

Summary of Contents for LTX



























Reviews:

No comments

Brands by name

Popular brands

Load more brands