manualshive.com logo in svg

Telect LTX, Install Manual

Share
Download
Telect LTX Install Manual Download Page 6

© Telect, Inc.  All rights reserved. 148326 09.08.16 v2
1.509.926.6000  ::  telect.com

6

LTX Patch and Splice Panel

LTX Patch and Splice Panel

Fiber :: Install guide

This manual provides a comprehensive overview of and installation guidelines for the LTX Patch and Splice Panel. While care has been taken 
to defi ne all necessary information, complete details may not be covered. If you have any questions, contact Telect Technical Support at 
[email protected] or call 1.509.926.6000.

Throughout this guide, relevant and crucial information is displayed in the form of Notes, Alerts, Cautions, and Warnings. These notifi cations 
are prominently displayed and their importance is indicated as follows: 

NOTE:  General information the user should pay special attention to.

Alert!  Important information and/or instructions the user should adhere to.

CAUTION!  Indicates a hazardous situation, which if not avoided could result in minor or moderate injury.

WARNING:  Indicates a potentially hazardous situation which if not avoided could result in death or serious injury.

Telect assumes no liability from the application or use of these products. Neither does Telect convey any license under its patent rights of 
others. This document and the products described herein are subject to change without notice.

1.2  About this Guide 

1.3  Terminology

Acronym/Abbreviation

Term

IF

IntraFacility Fiber

IFC

IntraFacility Cable

LC

Local Connector

MPO

Multi-fi ber Push-On optical fi ber module interface type

NE

Network Element

NEBS

Network Equipment Building System (telecommunications product safety equipment rating standard)

PC

Physical Contact fi ber optic connector (single or multimode)

SC

Standard Connector

TIA

Telecommunications Industry Association

TIA/EIA-568 B.3

Telecommunication standards for commercial cabling

TUV

Technical Inspection Association (global product certifi cation compliance marking)

UL

Underwriter Laboratories (electrical standards)

UPC

Ultra Physical Contact fi ber optic connector (single or multimode)

The following list of acronyms and abbreviations are used throughout this manual.

Summary of Contents for LTX



























Reviews:

No comments

Brands by name

Popular brands

Load more brands