Telair ENERGY 4004D Use And Maintenance Manual And Instructions For Installation Download Page 22

 

 

Energy 4004 D 

Vers. 007

 

 

GB

22 

 

GENERAL WARRANTY TERMS 

 

TELAIR 

guarantees its products against any material and/or manufacturing 

faults and defects. 

 

The entitlement to warranty cover for new engines is valid for a period of 
24 months from the time of handing over to the end user, or for a maxi-
mum of 2000 operating hours, whichever of these limits is reached first. In 
all cases the warranty period shall lapse no later than 26 months (28 
months if delivered outside Europe) after delivery ex factory. 
 
For electric and hydraulic components, pipes, belts, sealing elements, in-
jection nozzles, clutches, gear boxes, the warranty term is 12 months from 
the time of handing over to the end user, or for a maximum of 2000 operat-
ing hours, whichever of these limits is reached first. In all cases the war-
ranty period shall lapse no later than 14 months (16 months if delivered 
outside Europe) after delivery ex factory. 

 

In any case, the costs of lubricants and consumables shall be charged. 
Any transport expenses shall be intended as to be covered by the purchaser; 
the same applies to any expenses connected with inspections requested by the 
customer and accepted by 

TELAIR

 
In any case, the costs of lubricants and consumables shall be charged. 
 
The manufacturer’s warranty shall only be valid if: 
•  the customer has carried out any routine maintenance according to the rec-

ommended schedule and has promptly visited the nearest after-sale centre if 
required. 

•  the customer can produce a document showing the date of sale (invoice or 

receipt). 

  Such document will have to be kept with care and be intact when produced to 

the 

TELAIR

 After-Sales centre on requesting service. 

 
In any case, the purchaser shall not be entitled to: 
•  terminate the contract; 
•  claim damages to persons or property; 
•  ask that the warranty be extended in the event of product defects or malfunc-

tioning. 

 

Summary of Contents for ENERGY 4004D

























Reviews: