background image

 

4

Model 4000 WPP Upgrade

Version 6.0R2 

 

Provided Materials

 

 

A new upper printed circuit board (PCB), Tektronix Part #068977-00 
(REV C).

 

 

A set of new keycaps.

 

 

Software upgrade diskette. (Version 6.0 or later).

 

Required Tool (Not Provided)

 

 

5/16-inch nut driver.

 

Step-By-Step Board and Keycap Upgrade Procedure

 

1.

 

Raise the lid of the switcher panel. 

 

2.

 

Power down the switcher panel.

 

CAUTION

 

To avoid static damage to sensitive electronic devices, protect the Model 4000-
3 Digital Switcher from static discharge. Avoid handling switcher modules in a 
high static environment. Touch the grounded metal of the switcher before you 
remove any modules. This helps ensure that any potential difference between 
your body and the switcher is dissipated. Always use a grounding strap and 
grounded equipment when you handle switcher PCBs and ribbon cables.

 

3.

 

Remove the new circuit board from the static protective bag in which it 
was shipped. Lay the empty bag across the horizontal PCB in the 
bottom of the switcher panel housing to protect it and to catch any nuts 
that might be accidently dropped from above during the following 
steps. 

 

WARNING

 

Electrical potential is still applied to some internal components even when 
the power switch/breaker is in the off position. To prevent electrical shock 
when working on this equipment, disconnect the AC line cord from the AC 
source before working on any internal components. A residual voltage may 
be present immediately after unplugging the system due to large power 
supply capacitors discharging. Wait thirty seconds to allow capacitors to 
discharge before working on the system.

4.

 

Detach the seven ribbon cables from the originally installed #068977-00 
PuP board. (It is the top-most rectangular PCB.) 

 

Do not

 

 detach the other 

ends of the cables. Leave those cables dangling in place for eventual re-
connection.

 

CAUTION

 

Some of the following operations require an assistant to insure that PCBs are 
properly supported while screws or nuts are removed and replaced. Failure to 
properly support PCBs could result in damage.

Summary of Contents for 4000-3











Reviews: