background image

 

Contacting Tektronix

 

Copyright © Tektronix, Inc. All rights reserved.

This document may not be copied, in whole or in part, or otherwise reproduced, except as specifically 
permitted under U.S. copyright law, without the prior written consent of Tektronix, Inc., P.O. Box 1000, 
Wilsonville, Oregon 97070-1000. TEKTRONIX is a registered trademark and Grass Valley is a trade-
mark of Tektronix, Inc. All registered trademarks and trademarks are property of their respective hold-
ers. Tektronix products are covered by U.S. and foreign patents, issued and pending. Product options 
and specifications subject to change without notice. The information in this manual is furnished for in-
formational use only, is subject to change without notice, and should not be construed as a commitment 
by Tektronix, Inc. Tektronix assumes no responsibility or liability for any errors or inaccuracies that 
may appear in this publication.

 

Voice

Fax

Addresses

Web Site

Customer 
Support

 

North America

(800) 547-8949

(530) 478-3181

Tektronix, Inc.
Tektronix Grass Valley Products
P.O. Box 1114
Grass Valley, CA 95945, USA

http://www.tektronix.com

Elsewhere

Distributor or sales office from which 
equipment was purchased.

 

Product, 
Service, Sales 
Information

 

North America

(800) 547-8949

(503) 627-7275

Tektronix, Inc.
Video and Networking Division
P.O. Box 500
M.S. 58-965
Beaverton, OR 97077-0001, USA

http://www.tektronix.com

Europe 

44 (10) 1628 40 3300

44 (0)1628 40 3301

Asia

(852) 2585-6688

(852) 2802-2996

Japan

81 (3) 5992 0621

81 (3) 5992 9377 

Latin America

(305) 477-5488

(305) 477-5385

Summary of Contents for 4000-3











Reviews: