Teeter 600ia Assembly Instructions Manual Download Page 11

Step   5

Install the Front Ankle Bar Assembly (F5-1045) into the Main Shaft (IA-1600)

• Insert the Front Ankle Bar (F5-1045) into the Front Ankle Bar Housing (Figure 13). Pull up 

on the T-Pin Lock to insert the Front Ankle Bar all the way and release in the shortest setting 

(the hole closest to the Front Ankle Bar). 

• From the reverse side, pull on the zip-tie to stretch the Retainer Spring and Cable Loop so 

that they align with the hole at the back of the Front Ankle Bar Housing (Figure 14).

• Insert the Bolt (H1-1212) through the hole, Retainer Spring, Cable Loop, and the hole on the 

other side of the housing (Figure 14A). 

• Tighten the Nut (H1-3010) using the 13mm Open Wrench (F5-1088) provided.  
• Cut the long portion of the zip-tie with scissors and cover the open end with the End Cap 

(F5-1050) (Figure 14B).

WARNING

!

Failure to assemble the T-Pin Ankle Lock System properly could 

result in serious injury or death!

1

FIGURE 14

FIGURE 14A

FIGURE 14B

1

FIGURE 13

VIEWS FROM BACK

1

Retainer Spring & Cable Loop

Front Ankle Bar Housing 

1

Summary of Contents for 600ia




















Reviews: