TECO JSDE Series Manual Download Page 39

Page: 39 / 62

Parameter

Name & Function

Default

Unit

Setting

Range

Control

Mode

Chapter

Cn027

Reserve parameter

─

Cn028

Reserve parameter

─

Reset parameters.

Setting Explanation

0 Disabled

★

Cn029

Reset all Parameters to default (Factory
setting)

0 X

│

ALL 5-6-10

Servo motor model code

★

Cn030

Servo model code can be display and checked with
parameter dn-08, refer

3-2-2 dn-08

table for more

information. (refer to chapter 1-1-3)
Attention

：

Before operate your servo motor., check this

parameter setting is compatible for servo drive and
motor. If there has any incompatible problem contact
supplier for more information.

Default

X X ALL

3-2-2

Cooling fan running modes

(Only available for the model which equip with fan.)

Setting Explanation

Run when Servo ON.

2 Always

Running.

Cn031

3 Disabled.

1 X

│

ALL 5-6-8

Speed feed back smoothing filter

Cn032

Restrain sharp vibration noise by the setting and this

filter also delay the time of servo response.

500 Hz

│

1000

5-3-12

Speed Feed-forward smoothing filter

Cn033

Smooth the speed feed-forward command.

40 Hz

│

100

5-4-6

Torque command smoothing filter

Cn034

Restrain sharp vibration noise by the setting and this

filter delay the time of servo response.

0 Hz

│

1000

ALL 5-2-7

Panel display content selection

Select display content for LED panel for power on status.

Setting Explanation

Display data set and drive status parameter. Refer
3

Cn035

│

Display Un-01 ~ Un-19 content. Refer 3-2-1 for
more information.
Ex

：

Set Cn035=1, when power on it display the

actual speed of motor. (content of Un-01)

0 X

│

ALL

3-1

3-2-1

Summary of Contents for JSDE Series































































Search results

Summary of Contents for JSDE Series

Reviews:

Brands by name

Popular brands

TECO JSDE Series, Manual

Search results

Summary of Contents for JSDE Series

Reviews:

Brands by name

Popular brands