TECNA 2P2B00 Instruction Manual Download Page 32 | Manualshive

Page: 32 / 36

TECNA 2P2B00 Instruction Manual Download Page 32

PROVASET 2P code 2P2B00 - 2P6B00 - Instruction manual

rev. 14/02/2013

page 32

GUARANTEE

tecna srl

guarantees its products for 12 months starting from the delivery date in terms of

production and material defects.

The delivery date is the one on the Transport Bill (DDT) issued by

tecna srl

when delivering

the goods to the customer or the carrier for delivery.

The parts damaged by transport, the tester subject to a wrong or bad installation and/or
maintenance as well as to improper uses, negligence or use incapacity, or again to
tampering by unauthorised persons and anyway to causes not depending on

tecna srl

are

not covered by the guarantee.

The guarantee is valid only towards the original buyer.

During guarantee period, each maintenance, repair or replacement of parts can only take
place at

tecna srl

seat.

The tester transport is up to the Customer, with the enclosed technical service request (see
next page).

The producer refuses any responsibility for any direct or indirect damage due to the use of

the supplied products different from the proper use described in this manual and/or to their

failed or wrong operation.

The only competent court for any controversy arising from the execution or interpretation of
this guarantee is the one of Modena. The applicable law is the Italian one.

USER INFORMATION EUROPEAN DIRECTIVE 2002/96/EC - 2003/108/CE

This product is conforms to European Directive 2002/96/EC - 2003/108-CE.
This appliance bears the symbol of the barred waste bin. This indicates that, at
the end of its useful life, it must not be disposed of as domestic waste, but must
be taken to a collection centre for waste electrical and electronic equipment,
or returned to a retailer on purchase of a replacement.
It is the user's responsibility to dispose of this appliance through the appropriate
channels at the end of its useful life.
Proper differential collection, and the subsequent recycling, processing and

environmentally compatible disposal of waste equipment avoids unnecessary damage to
the environment and possible related health risks, and also promotes recycling of the
materials used in the appliance.

«
...
30
31
32
33
34
...
»

Summary of Contents for 2P2B00





































Reviews:

No comments