TECNA 2P2B00 Instruction Manual Download Page 22

Page: 22 / 36

PROVASET 2P code 2P2B00 - 2P6B00 - Instruction manual

rev. 14/02/2013

page 22

6.2

"TEST TABLE SELECTION" select menu

Select the number of the operative test table for the tests with the

[+]

[-]

keys, by confirming

with key

↵

]

: NUMBER OF THE OPERATIVE PARAMETER TABLE

Range 1

NOTE:

The number of the operative test table can be programmed also inside the

"CONFIGURATION AND OPTIONS" menu (see par. 6.1)

6.3

"TEST TABLES" modify menu

Select the number of the test table to be changed.
Select the parameter to be changed with the

[

↓

]

key.

Change the numerical selected parameter with the

[+]

key to increase or with the

[-]

key to

decrease and confirm the change (blinking parameter) with button

↵

]

PARAMETERS

DESCRIPTION

RANGE

FILLING PHASE

0.0

99.9 s or 0

999 s

SETTLING PHASE

0.1

99.9 s or 1

999 s

MEASUREMENT PHASE

0.1

99.9 s or 1

999 s

TEST PRESSURE

SCALE RANGE

PRESSURE DELTA

SCALE RANGE

PROVASET

– Test parameters table and programmable ranges

SCALE

2P2B00

RANGE

2P6B00

RANGE

mmH2O 0

20394 0

61182

mbar

2000.0 0

6000.0

kPa

200.00 0

600.00

mmHg 0

1500.0 0

4500.0

PSI

30.00

90.00

inH2O

802,5 0

2407,5

PROVASET

–Programmable pressure scales and ranges

SELECT

TABLE n. XX

T1 xx.x mmH20

T2 xx.x Pr

YYYY

T3 xx.x Dp

PROGRAMMING

TEST TABLE

SELECTION

[

↓

]

PROGRAMMING

TEST TABLES

[

↓

]

MODIFY

TABLE n. XX

T1 xx.x mmH20

T2 xx.x Pr

YYYY

T3 xx.x Dp

Summary of Contents for 2P2B00





































Search results

Summary of Contents for 2P2B00

Reviews:

TECNA 2P2B00, Instruction Manual, Page: 22 / 36

Search results

Summary of Contents for 2P2B00

Reviews: