Technogel FREEZER 200/1 Instructions For The Installation, Use And Maintenance Download Page 4 | Manualshive

Page: 4 / 49

background image

4



Instructions for lifting the machine

FREEZER 200/1 - NET WEIGHT = 460 kg.

Raise the machine using a fork lift truck, inserting
the forks under the sides of the machine between
the front and rear wheels.

Lift the machine using belts as shown in the figure
positioned close to the front and rear wheels. The cable
used to raise the machine must be positioned exactly in
the center of the machine.

HOW TO MOVE THE MACHINE

Move the machine using a manual pallet trolley.
Insert the trolley forks either under the side or the
front of the machine.

After positioning the machine, make sure all four legs
rest on the ground. Regulate the feet so that the
machine tilts forward slightly.

«
...
2
3
4
5
6
...
»

Summary of Contents for FREEZER 200/1


















































Reviews:

No comments

Related manuals for FREEZER 200/1

Brand: Buffalo Tools Pages: 8

Brand: Iceking Pages: 13

Brand: ZANKER Pages: 36

Commercial Cool CCFE35

Brand: W APPLIANCE Pages: 16

MARLEY AV 98-1514E

Brand: SPX Cooling Technologies Pages: 32

Brand: Baumatic Pages: 28

Brand: AEG Pages: 92

Brand: AEG Pages: 44

Brand: Frigomat Pages: 64

Brand: Foster Pages: 4

Brand: Morgan Pages: 4

Brand: Faber Pages: 5

Brand: White Knight Pages: 6

Brand: NABO Pages: 64

Brand: Parker Hiross Pages: 60

Brand: Zanussi Electrolux Pages: 16

Brand: Candy Pages: 124

Brand: WC Wood Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands