Technogel FREEZER 200/1 Instructions For The Installation, Use And Maintenance Download Page 42

Page: 42 / 49



Support unit with flange and ventilator

Pos.

Name of component

Code

Aluminium freezer holder support and support

FR1-3719.0/10

Freezer pipe flange

FR1-4480.3/10

O-ring for flange

FR3-0037

Mixture inlet mouth seal

R.013.32

Stainless steel protection flange

FR1-3713.0

Complete support

FR1-7257.4

Turbine drawing shaft

FR1-1741.0/20

Oil protection rotating seal

GU-7256.6

Spacer

FR1-1820.0/01

Bearing

CS-7255.6

Aluminium support body

FR1-3717.0/20

Bearing

CS-7254.6

Bearing

CS-7255.6

Greaser attachment

GU-7331.6

Ventilator

DFA-5048.6

Support pulley 1

stage with 5 grooves

Support pulley 2

stage with 6 grooves

FR1-1740.0/10
FR6-0105

Pulley locking flange

FR1-4522.0/10

Summary of Contents for FREEZER 200/1


















































Search results

Summary of Contents for FREEZER 200/1

Reviews:

Related manuals for FREEZER 200/1

Brands by name

Popular brands

Technogel FREEZER 200/1, Instructions For The Installation, Use And Maintenance

Search results

Summary of Contents for FREEZER 200/1

Reviews:

Related manuals for FREEZER 200/1

Brands by name

Popular brands