Technogel FREEZER 200/1 Instructions For The Installation, Use And Maintenance Download Page 41

Page: 41 / 49



COMPONENTS LIST FOR REFRIGERATING SYSTEM FREEZER 200/1

Pos.

Part name

FREEZER

200/1

Part Number

Freezer tube

FR1-5075.3

Refrigerating compressor:

- DORIN         V 220/380           50 Hz
                     V 220/380              60 Hz
                     V 200       50-60 Hz

- COPELAND V 220/240 -380/415  50 Hz

CP-25034.6
CP-25035.6

Cylinder condenser:
Copper concentric tubes condenser
Liquid receiver

FR1-023

Gas filter

CD-5623.6/M

Gas pilot light

M2-0049

Solenoid valve without electric coil
- electric coil only V 24-50/60 Hz

VV-5614.6
VV-5616.6

Thermal expansion valve

VT-9020.6

High/low pressure switch

TR-5714.6

Water pressure switch valve

FR3-0095

Low pressure gauge (evaporation)

FR6-0064

High pressure gauge (condensation)

FR6-0065

Hot gas solenoid valve without electric coil
- electric coil only V 24-50/60 Hz

VV-5614.6
VV-5616.6

Hot gas injection valve (for details see page )

FR1-5158.3

Knob with gravitational indicator
- gravitational indicator only

FR1-3820.0

FR3-0199

Force piping vibration-damping flexible tube

ME-0101

Return piping vibration-damping flexible tube

FR3-0008

Condenser tap

FR6-0244

Compressor timing case resistor
- for FRASCOLD compressor
- for DORIN compressor
- for BITZER compressor
- for COPELAND compressor

FR3-0004

CP-012

Oil pressure switch (only where equipped)

Summary of Contents for FREEZER 200/1


















































Search results

Summary of Contents for FREEZER 200/1

Reviews:

Related manuals for FREEZER 200/1

Brands by name

Popular brands

Technogel FREEZER 200/1, Instructions For The Installation, Use And Maintenance

Search results

Summary of Contents for FREEZER 200/1

Reviews:

Related manuals for FREEZER 200/1

Brands by name

Popular brands