Technogel FREEZER 200/1 Instructions For The Installation, Use And Maintenance Download Page 23 | Manualshive

Page: 23 / 49

background image

23

Technical assistance

WARNING DANGER !!!

Work carried out on the machine by unauthorized personnel can prove dangerous.

We therefore advise you to call THE AUTHORIZED TECHNICAL SERVICE in case of any fault in the
machine.

TECHNOGEL DISCLAIMS ALL RESPONSIBILITY FOR ANY DAMAGE ARISING FROM

TECHNICAL INTERVENTION CARRIED OUT BY UNAUTHORIZED PEOPLE

TECHNOGEL ALSO DISCLAIMS ALL RESPONSIBILITY FOR DAMAGE CAUSED BY

THE USE OF NON-ORIGINAL SPARE PARTS WHICH HAVE NOT BEEN APPROVED

FOR USE ON MACHINES MANUFACTURED BY THE COMPANY.

The next few pages give

INSTRUCTIONS RESERVED FOR THE TECHNICAL SERVICE

with the technical

information for each type of machine.

«
...
21
22
23
24
25
...
»

Summary of Contents for FREEZER 200/1


















































Reviews:

No comments

Related manuals for FREEZER 200/1

Brand: Oster Pages: 26

Brand: Smeg Pages: 14

Brand: NEFF Pages: 106

Brand: Sub-Zero Pages: 2

Brand: LG Pages: 14

Brand: LG Pages: 36

LRTBC1825T Service

Brand: LG Pages: 38

LRTP-1231W precautio

Brand: LG Pages: 45

LRTP-1231W precautio

Brand: LG Pages: 2

Brand: LG Pages: 76

LRTBC1825T Service

Brand: LG Pages: 16

Brand: LG Pages: 36

Brand: LG Pages: 84

Brand: LG Pages: 84

Brand: LG Pages: 116

Brand: HELLER Pages: 8

ACTIVESMART RS36A80

Brand: Fisher & Paykel Pages: 88

Brand: SCAN domestic Pages: 25

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands