Technogel FREEZER 200/1 Instructions For The Installation, Use And Maintenance Download Page 11

Page: 11 / 49

Description of machine control panel

Pos.

Components

Function

white button "RESET" machine power

illuminated

button

applied

voltage

Off = Power off button

Potentiometer overrun

Nel l'air regulator iced

Push button start / stop "group bombs"

Starts and for pumps

Ice cream production Viewer

Displays the time-liter ice cream produced

Push button start / stop "agitator"

Starts and for the agitator (turbine)

Push button start / stop "refrigerator
compressor"

”

Starts and stops the compressor fridge

Switchboard Meter

Controls and displays ice hardness

Push ON / OFF "hot gas"

Hot Gas ON = consent for the injection of hot
gas

from

the

remote

OFF = Hot gas injection to stop

Manual valve regulating "hot gas" with
gravitational gauge connected

Turning it counterclockwise, hot gas is
introduced. Indicative quantity is detected on
the pressure gauge on the wheel.

Alarm lamp

Notice engine failure or shutdown the machine

Pushbutton "emergency"

Pressing it will be for the entire machine.

Indicator compressed air flow

Nel air Indicator% cream in the regulation is
check with the potentiometer (2)

Pressure gauge indicating the pressure /
temperature

condensation

the

refrigeration

Indica, with the machine running. pressure /
condensing temperature

Pressure gauge indicating the pressure /
temperature

Evaporation

the

refrigeration

Indica, with the machine running, the pressure
/ temperature evaporation

Summary of Contents for FREEZER 200/1


















































Search results

Summary of Contents for FREEZER 200/1

Reviews:

Related manuals for FREEZER 200/1

Brands by name

Popular brands

Technogel FREEZER 200/1, Instructions For The Installation, Use And Maintenance

Search results

Summary of Contents for FREEZER 200/1

Reviews:

Related manuals for FREEZER 200/1

Brands by name

Popular brands