manualshive.com logo in svg

Technicolor MediaConnect TG234, Setup And User Manual

Share
Download
Technicolor MediaConnect TG234 Setup And User Manual Download Page 12

9

1 Getting started

DMS3-CTC-25-221 v1.0

1.2.4 Mode switch

The mode switch allows you to switch between modes of your TG234:

Station

:

Choose this mode when the TG234 is acting as a 5 GHz wireless client. The Ethernet port of the TG234 will be 
connected to your network client (typically a set-top box).

Access Point

:

Choose this mode when the TG234 is acting as a 5 GHz wireless access point. The Ethernet port of the TG234 will be 
connected directly to your Internet gateway, the other can be used to connect an Ethernet device to your Internet 
gateways network.

Repeater

:

Choose this mode when the TG234 is acting as a 5 GHz wireless repeater.

Auto

:

The TG234 will automatically select the correct mode (station, access point or repeater) depending on the current 
connection conditions. 

For more information, see 

“2 Setup” on page 12

.

How the TG234 chooses the correct mode when switched to Auto

The TG234 will switch to:

Station

 mode if the TG234 was connected to an Ethernet device (for example: a set-top box) at start-up.

Access point

 mode if the TG234 was connected to a gateway or router (or similar) at start-up.

Repeater

 mode if the TG234 is wirelessly connected to an access point and no device is connected to the Ethernet port. 

This can happen in the either of the following cases:

After successfully running WPS with no devices connected to the TG234 Ethernet port.

After removing the cable when the device was in 

Station

 mode.

When the 

TG234

 is in station mode and you selected the 

Repeater

 check box in the TG234 GUI. 

For more information, see 

“The Basic settings” on page 23

.

TG234

Mode switch

After moving the switch to another mode, turn off the TG234 and turn it back on. The TG234 will then activate the 
new mode at start up.

Summary of Contents for MediaConnect TG234























































Reviews:

No comments

Brands by name

Popular brands

Load more brands