return to the main screen at once. If you don’t press any key
for 1 or 2 seconds after a selection the call melody will be
played in full length in the speaker and selected also. Then
the display will return to the main screen.
8) Monitor function
In normal mode the unit is always in reception mode. This
would cause a disturbing noise on free channels. Therefore
the unit is equipped with a noise suppression circuit
( squelch ) for reception mode. It cuts off the disturbing noise,
which the receiver produces on free channels, and lets pass
only the speech signals of a counter station to the speaker.
While the squelch is open display shows the symbol R at the
position ( E ). In case of very weak signals it may occur, that
the squelch remains closed. If you want to make also these
signals audible, you can inhibit the squelch ( monitor function ).
To this end depress out of the keys ( 4 ) Down
▼
2 times or
Up
▲
6 times. The display shows the writing . Then,
depress briefly the confirmation key ( 5 ). Now the squelch is
always open and you can hear a noise on free channels. In
the display you can see , where the “8“ stands for the
actual channel number in the actual band. This is the sub-
screen for monitor operation. In this condition you can only
adjust the volume level setting ( Para 4 ) or the squelch sen-
sitivity setting ( Para 5 ). To adjust the volume level of the
reproduction of incoming signals depress the volume key ( 8 ).
See paragraph 4 for the further instructions. To adjust the
squelch sensitivity setting for incoming signals depress out of
the keys ( 4 ) Down
▼
once or Up
▲
once. See paragraph 5
for the further instructions. To reactivate the squelch,
depress in the sub-screen for monitor operation the confir-
mation key ( 5 ), and the display will return to the normal
main screen.
left side of the writing “off“ and then depress the confirmati-
on key ( 5 ). After this entry the display returns to the main
screen. On the position of the microphone symbol ( A )
you see the transceiver symbol
again. This indicates that
the VOX function is no longer active.
The adjustment of the threshold of the sound level at which
the transmitter starts to work, can be executed at inactive or
active VOX function. To this end depress out of the keys ( 4 )
Down
▼
4 times or Up
▲
4 times. The display shows the writ-
ing . Then, depress briefly the confirmation key ( 5 ).
Then, the display shows or . Now put the arrow on
the left side of the microphone symbol below and then
depress the confirmation key ( 5 ). Then the display shows
, the microphone symbol with one or several points or
bars. The number of those points or bars shows the actual
setting of the VOX sound level threshold. The more points or
bars appear, the louder you have to speak to start the trans-
mission. By the help of the Up/Down keys ( 4 ) this setting
can be changed and watched in the display. At the highest or
lowest value you hear a triple confirmation tone. Press the
confirmation key ( 5 ) to select the desired setting of the
sound level threshold, and the display will return to the main
screen.
7) Selection of the call melody
To select a call melody depress out of the keys ( 4 ) Down
▼
3 times or Up
▲
5 times. The display shows the writing
Tone. Then depress briefly the confirmation and On/Off key
( 5 ). Then the display shows , a music note symbol
and a digit. The digit stands for the number of the actual call
melody. By the help of the Up/Down keys ( 4 ) the call melo-
dy numbers can be changed from 1 to 8 in the wanted direc-
tion in a ring like system. By pressing the confirmation key
( 5 ) you select the desired call melody, and the display will
English
32
English
33
MON
on?
VOX
MON
8
Manual_UHF-Handy 18.07.2003 16:53 Uhr Seite 32
