background image

- 1 -

USER'S MANUAL

Read this information before using your product.

Acknowledging Special Precautions and the FCC Notice Cautions.

Modifications not expressly approved by the party responsible for compliance could void the

user's authority to operate the equipment.

FCC compliance Information

This device complies with part 15 of FCC Rules.

Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received.

Including interference that may cause undesired operation.

Information to User

This equipment has been tested and found to comply with the limits for a Class B digital

device, Pursuant to part 15 of the

FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio Frequency energy and, if not

installed and used in accordance with th einstruction, may cause harmful interference to

radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television reception, whic h can

be determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

> Reorient or relocate the receiving antenna.

> Increase the separation between the equipment and receiver

> Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Summary of Contents for PK-400NW










Reviews: