background image

409-10095 

Rev

 H

 

of 12 

SUPPORT CENTER

 

CALL TOLL FREE 1-800-522-6752 (CONTINENTAL UNITED STATES AND PUERTO RICO ONLY) 

The 

Support Center

 offers a means of providing technical assistance when required. 

In addition, Field Service Specialists are available to provide assistance in the adjustment or repair of the 
application equipment when problems arise which your maintenance personnel are unable to correct. 

INFORMATION REQUIRED WHEN CONTACTING THE SUPPORT CENTER 

When calling the Support Center regarding service to equipment, it is suggested that a person familiar with the 
device be present with a copy of the manual (and drawings) to receive instructions. Many difficulties can be 
avoided in this manner. 

When calling the Support Center, be ready with the following information: 

1.  Customer name 

2.  Customer address 

3.  Person to contact (name, title, telephone number, and extension) 

4.  Person calling 

5.  Equipment number (and serial number if applicable) 

6.  Product part number (and serial number if applicable) 

7.  Urgency of request 

8.  Nature of problem 

9.  Description of inoperative component(s) 

10.  Additional information/comments that may be helpful 

 

 

Summary of Contents for 2031400-1













Reviews: