background image

IMPORTANT SAFETY INSTRUCTIONS

1

Read these instructions.

Keep these instructions.

Heed all warnings.

Follow all instructions.

Do not use this apparatus near water.

Clean only with dry cloth.

Do not block any ventilation openings. Install
in accordance with the manufacturer's
instructions.

Do not install near any heat sources such as
radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce
heat.

Do not defeat the safety purpose of the
polarized or grounding-type plug. A polarized
plug has two blades with one wider than the
other. A grounding type plug has two blades
and a third grounding prong. The wide blade
or the third prong are provided for your safety.
If the provided plug does not fit into your
outlet, consult an electrician for replacement
of the obsolete outlet.

10  Protect the power cord from being walked on

or pinched particularly at plugs, convenience
receptacles, and the point where they exit
from the apparatus.

11  Only use attachments/accessories specified

by the manufacturer.

12 

Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the
apparatus. When a cart is used, use
caution when moving the
cart/apparatus combination to avoid

injury from tip-over.

13  Unplug this apparatus during lightning storms

or when unused for long periods of time. 

14 Refer all servicing to qualified service

personnel. Servicing is required when the
apparatus has been damaged in any way, 
such as power-supply cord or plug is
damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does
not operate normally, or has been dropped.

This equipment should be installed near the 
socket outlet and disconnection of the  device 

should be easily accessible.

Do not install in a confined space.

Do not open the unit - risk of electric shock 
inside.

Caution:

You are cautioned that any change or
modifications not expressly approved in this
manual could void your authority to operate this
equipment.

Service

There are no user-serviceable parts inside. 

All service must be performed by qualified 
personnel.

Warning!

To reduce the risk of fire or electrical shock, do
not expose this equipment to dripping or
splashing and ensure that no objects filled with
liquids, such as vases, are placed on the
equipment.

This apparatus must be earthed.

Use a three wire grounding type line cord like
the one supplied with the product.

Be advised that different operating voltages
require the use of different types of line cord
and attachment plugs.

Check the voltage in your area and use the
correct type. See table below:

Voltage 

Line plug according to standard

110-125V

UL817 and CSA C22.2 no 42.

220-230V

CEE 7 page VII, SR section 
107-2-D1/IEC 83 page C4.

240V

BS 1363 of 1984. 
Specification for 13A fused 
plugs and switched and 
unswitched socket outlets.

The lightning flash with an arrowhead
symbol within an equilateral triangle, is
intended to alert the user to the 
presence of uninsulated "dangerous volt-

age" within the product's enclosure that may be of
sufficient magnitude to constitute a risk of 
electric shock to persons.

The exclamation point within an
equilateral triangle is intended to alert
the user to the presence of important
operating and maintenance (servicing)

instructions in the literature accompanying the
product.

a

Summary of Contents for G-Sharp































Reviews: