background image

30

Marchesan Implementos e Máquinas Agrícolas “TATU” S.A.

RC² 2600 CL / RC² 2600 LSL / RC² 3100 CL

Lubrication

Lubrication points - Lubricate daily

Maintenance

ATTENTION

Manufacturer

Specification

FL-Lubricantes Tutela Alfa 2K grease

Castrol

EPL 2 grease

Shell

Alvania EP(LF) 2 grease

Ipiranga

Ipiflex EP 2 grease

Ipiranga

Litholine EP 2 grease

Texaco

Multifak EP2 grease

Observe daily if the nuts and bolts are tightened and the conditions of the pins and 

cotter pins.

The maintenance of the gearbox should be done in the following way:
• When starting to work and everyday of the first working week, check the oil level 

through the indicators of level and fill up if necessary.

• Then, verify the oil level monthly.
• Clean the grease fittings and insert a sufficient amount of fresh grease. Use the table 

below to see the indicated greases for the hub of the blades.

NOTE

• Do not add oil above the indicated level.
• For RC² 2600 CL and RC² 3100 CL models: the oil level on the double 

distributor is 2 liters and 2.85 liters on each gearbox.

• For the RC² 2600 LSL model: the oil level on the gearbox is 4.3 liters and 

3.4 liters on the velocity transmission.

• Use SAE 90 oil only.

Besides the indicated 

spots, it is necessary to 

lubricate all grease fittings.
To lubricate the universal 

joint of the right cardan on 

the RC² 2600 LSL model, lift 

the protection cover.

Summary of Contents for RC2 2600 CL









































Reviews: