Tarmo 323082, Manual

Page: 19 / 49

Turn off the engine
Before you switch off the generator, allow it to run briefly without installations so
that it can “cool down”.
Normal use:
1. Turn off all the installations that are connected, and disconnect the plug. Before
you switch off the generator, allow it to run briefly without installations so that it
can “cool down”.
1. Turn the switch of the plug to the “off” position.
2. After the engine has fully cooled, turn the gas cap ventilation hole to the “closed”
position in a counter-clockwise direction.
When turning off, moving, and storing the engine, make sure that the switches of
the gas cap ventilation hole and the engine are in the “closed” position.
Note! lf you need stop the engine urgently, turn the engine switch to the “closed”
position.
Technical Specification
Model 323082
Length*width*height (mm) 555 * 305 * 460
Net weight (kg) 22 kg
Engine
Engine type 4-stroke, overhead air valve, single-cyl-
inder
Exhaust quantity (diameter of tank, stroke) 60*40mm
Compression ratio 8.8:1
Rotation speed 4,300 rpm (intelligent accelerograph
closes)
Cooling system Compulsive cold wind
Ignition system Transistor
Gas capacity 0.4L
Gasoline tank capacity 3.5L
Spark plug A7RC
Noise leveI (ISO8528-10) 64db/7m
Displacement 113 CC
Dynamo
Prearranged frequency (Hz) 50 60
Rated pressure (V) 230 120 240
Rated current (A) 8,3 15,8 7.92
Rated power output (KVA) 1 900 W
Maximum power output (KVA) 2 200 W
DC output 12 V 6 A
Inverter yes
Electrical open circuit installation yes
Noise level (zero load ~ full load) / 7m 59–64 db / 7 m
Operation at high altitudes
At high altitudes, the standard carburetor air or gas mixture will become exces-
sively dense, degrading the engine’s functions and increasing gas consumption.
Even if you use the proper nozzle, engine horsepower will still decline be 3.5% as
the altitude by 300 meters.
The engine nozzle is designed for high-altitude areas. lf it is used at low altitudes,
the power output may decline, the unit may overheat, and the engine may be seri-
ously damaged on account of an excessively low air-to-gas ratio.
Cleaning
Keep all safety devices, air vents and the engine housing free of dirt and dust as
far as possible. Wipe the equipment with a clean cloth or blow it with compressed
air at low pressure. We recommend that you clean the device after each use. Clean
the equipment regularly with a moist cloth and some soft soap. Do not use cleaning
agents or solvents; these could attack the plastic parts of the equipment. Ensure
that no water can seep into the device.
Maintenance
The purpose of making a maintenance and adjustment plan is to keep the genera-
tor in the best working condition. Please check and maintain the generator accord-
ing to the following chart.
Warning! Please turn off the engine before you carry out any repair. If the engine
needs to run when being repaired, make sure the operating area is well ventilated,
as the exhaust contains toxic CO.
Note! Please use only components authorized by the company or other parts of the
same quality. Substandard components will damage the generator.
Maintenance chart:
Item/
Maintaining time by
stages (1). Please
maintain the generator
in specified months or
hours. Either month or
hour is ok
Usage At
A Time
The first
month or
20 hours
every
three
months or
50 hours
every six
months
or 100
hours
Every year
or 200
hours
Machine
Oil
Check •
Change • •
Air Filter
Check •
Clean • (1)
Spark
Plug
clean-ad-
justment
•
Change •
Burning
container
Clean Every 300 Hours (2)
Clearence
of Air-door
check-ad-
justment
• (2)
Gas tank
and filter
Clean • (2)
Gas route Check Every 2 years. Plase change if necessary.
Note:
1. If used in dirty places, the generator will need more regular maintenance.
2. Maintenance of the above items must be done by a competent person special-
ized in such machinery.
3. When used for commercial purposes, record the operating hours of the genera-
tor to determine the correct maintenance cycle.
Plug
ON / OFF
Engine switch
Gas cap ventilation hole
On
323082_aggregaatti_ko_fi-sv-en-et-lv-lt-ru_A4.indd 19 28.5.2019 9.16.38