TANDBERG Media Processing System MPS 800 Administrator'S Manual Download Page 83

Page: 83 / 179

D 13373.08
NOVEMBER 2007

MPS

Table of

Contents

TANDBERG

MPS

ADMINISTRATOR GUIDE

System Status

System Unit

Product Type - Shows the TANDBERG product type

•

Product ID - Shows the TANDBERG product id

•

Up Time in Seconds - Shows the uptime since last boot in seconds

•

Up Time - Shows the uptime since last boot in days, hours, minutes and seconds

•

System Information (1:3)

Software

Version - Shows the installed software version

•

Name - Shows the installed software name

•

Release Date - Shows the installed software release date

•

Configuration

Telephony - Shows the total number of telephone options

•

Video Telephony - Shows the total number of Video Telephone options

•

Advanced Video Options - Shows the total number of Advanced Video options

•

Encryption - Shows the total number of encryption sites

•

PRI Ports - Shows the total number of PRI port options

•

Serial Ports - Shows the total number of serial port options

•

Maximum Bandwidth - Shows the maximum bandwidth installed

•

Managed Resources

Conference - Shows the number of conferences available for scheduled conferences

•

Fully Featured Conferences - Shows the number of fully featured conferences available

•

for scheduled conferences

Encoders - Shows the number of encoders available for scheduled conferences

•

Telephony - Shows the number of telephone calls available for scheduled conferences

•

Video Telephony - Shows the number of video calls available for scheduled conferences

•

Advanced Video Option - Shows the number of advanced video calls available for

•

scheduled conferences

Encryption - Shows the number of encrypted calls available for scheduled conferences

•

Max Bandwidth - Shows the maximum bandwidth available for scheduled conferences

•

Max B Channel PRI - Shows the maximum number of B channels available for sched-

•

uled conferences

System Unit, Software, Configuration, Managed Resources

Introduction

Quick

Setup

Using

the MPS

System

Configuration

Installation

Gateway

Configuration

MCU

Configuration

Technical

Descriptions

Appendices

Main

System

Status

Summary of Contents for Media Processing System MPS 800




















































































































































































Search results

Summary of Contents for Media Processing System MPS 800

Reviews:

Related manuals for Media Processing System MPS 800

Brands by name

Popular brands

TANDBERG Media Processing System MPS 800, Administrator'S Manual

Search results

Summary of Contents for Media Processing System MPS 800

Reviews:

Related manuals for Media Processing System MPS 800

Brands by name

Popular brands