background image

D 13373.08
NOVEMBER 2007

MPS

Table of  

Contents

TANDBERG 

MPS

  

ADMINISTRATOR GUIDE

 

MCU Overview

MCU Conference Overview

Encryption  (Secure  Confer-

ence

TF

)

 The MCU supports Se-

cure Conference DES and AES.

Indicates  that  DES  (56 
bit) encryption is used.

Indicates  that  AES  (128 
bit) encryption is used.

Indicates that the confer-
ence is not encrypted.

Password

  For  privacy,  a  conference 

can be password protected.

Indicates that a valid password 
is  required  for  all  participants 
dialling in to the conference.

Indicates  that  the  conference 
is not password protected.

Allow Incoming Calls

Yes

• 

 Participants can dial in 

to the conference.

No

• 

  Incoming  calls  are  not 

allowed. The MCU must dial 
out to all participants.

Duration

 Shows the 

call  duration  of  the 
conference.

IP  Bandwidth

  Shows 

the  total  IP  bandwidth 
used in the conference.

ISDN  Channels

  Shows 

the total number of ISDN 
channels used in the con-
ference.

Conference Status 

When a conference is 

active  click  on  the  corresponding  confer-
ence name or number to see conference 
status in details. It is possible to change 
the conference name.

Videos

  Shows  the  number  of  connected 

video  sites  and  the  maximum  number  of 
allowed video sites in the conference.

Telephones

  Shows  the  number  of  con-

nected  telephones  and  the  maximum 
number of allowed telephones in the con-
ference.

Create a Conference 

Click  on  the 

1. 

Conference#:  Create 

New

 drop down list to select a confer-

ence and press 

OK

 button to create a 

new conference.
Click  on  the 

2. 

Create  New  Conference

 

button to create a new conference.
Click on 

3. 

[Create]

 in the conference list 

to set up a new conference.

Filter Conference Overview

Active

• 

 If selected all the active confer-

ences are shown

Inactive

• 

 If selected all the inactive con-

ferences are shown

Dynamic

• 

 If selected all the Ad Hoc cre-

ated conferences are shown

Search

 View a specific conference select-

ed by name using the Name search field.

MCU Conference Overview

38

Introduction

Quick 

Setup

System 

Status

System  

Configuration

Installation

Gateway  

Configuration

MCU  

Configuration

Technical  

Descriptions

Appendices

Main

Using  

the MPS

Summary of Contents for Media Processing System MPS 800




















































































































































































Reviews: