TANDBERG Media Processing System MPS 800 Administrator'S Manual Download Page 178

Page: 178 / 179

D 13373.08
NOVEMBER 2007

MPS

Table of

Contents

TANDBERG

MPS

ADMINISTRATOR GUIDE

Configuring LCS and MPS for SIP (6:6)

Configuring SIP Dial In Numbers

When

Server Active

has been verified, it is time to configure the ap-

propriate SIP Dial In Numbers for the MPS system. Navigate to MCU
Configuration > Dial In Numbers.

Within this screen, enter all the appropriate SIP URIs for the appropriate
Dial In Conferences and Single Dial In Numbers.

All SIP URIs, configured in the MPS, must be fully qualified domain
names with the domain name that is configured under the

Routing

configuration within the LCS.

The prefix, entered under the

Routing

configuration, must be in-

cluded within all of the SIP names for the MPS to properly receive
the calls.

Once all of the dial-in URIs are configured, the MPS is ready to make and
receive SIP calls from other SIP devices registered to the LCS network.

Verify the Configuration

Once the MPS has restarted, the Overview page of the MPS should show
that the SIP status is

Server Active

Please verify that the configuration is active before you continue.

Verification of SIP Server Active and Configuring of Dial In Numbers

Example #1:

If the domain name for the LCS server is <

lcs.int

> and the SIP prefix

for the MPS was configured as <

MPS*

>, your dial in numbers must begin

with <

MPS

> and end with <

@lcs.int

> in order to be valid, e.g.:

[email protected]

MS Live Communications Server

178

Introduction

Quick

Setup

Using

the MPS

System

Status

System

Configuration

Installation

Gateway

Configuration

MCU

Configuration

Technical

Descriptions

Main

Appendices

Summary of Contents for Media Processing System MPS 800




















































































































































































Search results

Summary of Contents for Media Processing System MPS 800

Reviews:

Related manuals for Media Processing System MPS 800

Brands by name

Popular brands

TANDBERG Media Processing System MPS 800, Administrator'S Manual

Search results

Summary of Contents for Media Processing System MPS 800

Reviews:

Related manuals for Media Processing System MPS 800

Brands by name

Popular brands