TANDBERG Media Processing System MPS 800 Administrator'S Manual Download Page 175 | Manualshive

Page: 175 / 179

background image

D 13373.08
NOVEMBER 2007

MPS

TANDBERG

MPS

ADMINISTRATOR GUIDE

Add a Route

When the MPS is configured as an Authorized Host to
the LCS, the LCS needs to be told what SIP URIs should
be forwarded to the MPS. This is done by configuring a
route in the Live Communocation Server.

The SIP URI to reach the MPS will be the combination of
the

User

and

Domain

fields.

Under the same server properties window (see previ-
ous page), select the

Routing

tab and press

Add…

to

open the Add Static Route dialog and add a new routing
pattern:

The

1.

User

field is used to specify which URIs will be

forwarded by this rule. Wildcards (

*

) are allowed.

In the

2.

Domain

box, enter the domain that will be used

with the SIP URI for the MPS. The SIP URI to reach
the MPS will be the combination of the user and
domain fields. Example: <

[email protected]

>

Under

3.

Next Hop

, select

IP Address

and enter the IP

address of the System Controller Board of the MPS.

Set

4.

Transport

to

TCP

Set

5.

Port

to

5060

.

Press the

6.

OK

button to save the route

Press the

7.

OK

button to close the properties window

of the server.

This completes the configuration of the LCS server.
Next, the MPS will need to be configured to use the LCS
server.

Configuring Microsoft Office Live Communications Server (LCS) 2005, SP1

This section will illustrate how to setup the Live Commu-
nication Server (LCS) to work properly with the MPS.

Example #1:

If you want all calls coming in to <

MPS

> to be forwarded to the MPS, enter <

MPS

> in the

User

field.

LCS does allow a wildcard entry. Enter the <

*

> character if a wildcard entry is desired. For example, if all calls beginning with <

MPS

> should

be forwarded to the MPS itself (e.g. <

[email protected]

>, <

[email protected]

>, <

[email protected]

>), then enter <

MPS*

> in the

user field.

In the

Domain

box, enter the domain that will be used with the SIP URI for the MPS. The complete SIP URI to reach the MPS will be the

combination of the user and domain fields. Example: <

[email protected]

>

Under

Next Hop

, select

IP Address

and enter the IP address of the controller card of the MPS. Make sure

Transport

is set to

TCP

and

Port

is

5060

. The completed route should look like the figure to the left. Press

OK

to save the route, and press

OK

again to close the Properties

window of the server.

Configuring LCS and MPS for SIP (3:6)

MS Live Communications Server

175

Introduction

Quick

Setup

Using

the MPS

System

Status

System

Configuration

Installation

Gateway

Configuration

MCU

Configuration

Technical

Descriptions

Main

Appendices

«
...
173
174
175
176
177
...
»

Summary of Contents for Media Processing System MPS 800




















































































































































































Reviews:

No comments

Related manuals for Media Processing System MPS 800

PACSystems RX7i

Brand: GE Pages: 317

Brand: D&R ELECTRONICS Pages: 12

PARTNER II Release 4.1

Brand: Lucent Technologies Pages: 363

Brand: WattMaster Pages: 104

Brand: Polyaire Pages: 20

Brand: WesAudio Pages: 65

Brand: VIS-A-VIS Pages: 4

Brand: Allmatic Pages: 32

Brand: SMA Pages: 64

Brand: Imesa Pages: 33

Brand: RCA Pages: 14

Brand: Mi-Light Pages: 5

Brand: Hitachi Pages: 242

SAAK66 - MINI HES W/CD PLAYER

Brand: Panasonic Pages: 14

Brand: JVC Pages: 101

Brand: Panasonic Pages: 12

Brand: Panasonic Pages: 11

Brand: Panasonic Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands