TANDBERG Media Processing System MPS 800 Administrator'S Manual Download Page 82

Page: 82 / 179

D 13373.08
NOVEMBER 2007

MPS

Table of

Contents

System Status

TANDBERG

MPS

ADMINISTRATOR GUIDE

SIP Status

Mode -

Shows if the SIP service is enabled or not.

Server Status

Show status towards the configured SIP server i.e. whether or
not the MPS can find a server. Possible states are:

INACTIVE - SIP server not in use

•

DNS FAILED - DNS not set, external DNS server not found

•

or SIP server address not found at DNS server

TIMEOUT - SIP server not answering.

•

UNABLE CONNECT TCP - Unable to connect to SIP server

•

on TCP

ACTIVE - Normal case, when server is found.

•

UNKNOWN - Status unknown

•

Server Address -

Shows the connected SIP server address. If

no server is selected, the normal state will be Off

Server Authentication -

Shows if server NTLM or Digest

Authentication is turned On or Off

Registration

One status line for each possible conference, all with their
own unique SIP URI. Possible states are:

INACTIVE - No SIP URI’s have been logged on to server. In

•

cases where the server Authentication is off, the different
SIP URI’s don’t need to be registered, and will be reported
as inactive

REGISTERING - The server is registering the Conference

•

URI

REGISTERED - The Conference URI is registered on the SIP

•

server.

DEREGISTERING - The conference URI is deregistering

•

from the SIP server.

FAILED - The SIP server failed to register the URI

•

SIP Status

Introduction

Quick

Setup

Using

the MPS

System

Configuration

Installation

Gateway

Configuration

MCU

Configuration

Technical

Descriptions

Appendices

Main

System

Status

Summary of Contents for Media Processing System MPS 800




















































































































































































Search results

Summary of Contents for Media Processing System MPS 800

Reviews:

Related manuals for Media Processing System MPS 800

Brands by name

Popular brands

TANDBERG Media Processing System MPS 800, Administrator'S Manual

Search results

Summary of Contents for Media Processing System MPS 800

Reviews:

Related manuals for Media Processing System MPS 800

Brands by name

Popular brands