TANDBERG 2000 MXP User Manual Download Page 234

Page: 234 / 314

TANDBERG 2000 MXP

220

6.1.2 Audio

4 Audio Inputs

2 microphone inputs (balanced, 24V phantom powered) via XLR connectors.

2 audio inputs (line level) via RCA connectors.

All audio inputs are active by default. For further information, refer to chapter

Audio

Audio input connector specification:

Connector label

Microphone(s)

Audio input(s)

Signal type

Balanced

Unbalanced

Connector (codec)

XLR-F, pin 1-gnd, pin 2 hot,
pin 3-cold/neutral

Female RCA/phono, sleeve-
ground, centre-signal

Input impedance

2400 ohms (pin 2 - 3)

10K ohms

Max input level when set to
minimum input level

83 mVpp

15.5 Vpp

Max input level when set to
maximum input level

6.2 mVpp

1.2 Vpp

Range, menu adjustable
input gain

22.5 dB (16 steps of 1.5 dB)

Phantom power voltage

24 V +/- 5%

Phantom power resistor, pin
2

1200 ohms

Phantom power resistor, pin
3

1200 ohms

Max phantom power current
pr mic

12 mA

2 Audio Outputs

2 outputs (line level) via RCA connector providing audio from far end in addition to dial
tones. These outputs are used by the monitor loudspeakers.

Audio output connector specification:

Connector label

Audio outputs

Signal type

Unbalanced

Connector (codec)

Female RCA/phono, sleeve-ground, centre-
signal

Output impedance

680 ohms

Max output level when set to maximum
output level and volume control set to max.
PAL
NTSC
Max output level when set to minimum
output level and volume control set to max.
PAL
NTSC

0.75 Vpp
1.75 Vpp

0.75 Vpp
1.15 Vpp

Summary of Contents for 2000 MXP



























































































































































































































































































































Search results

Summary of Contents for 2000 MXP

Reviews:

Related manuals for 2000 MXP

Brands by name

Popular brands

TANDBERG 2000 MXP, User Manual

Search results

Summary of Contents for 2000 MXP

Reviews:

Related manuals for 2000 MXP

Brands by name

Popular brands