manualshive.com logo in svg

SynthCube FuzzBass TTSH, Build Manual, Page: 26 / 52

Share
Download
SynthCube FuzzBass TTSH Build Manual Download Page 26

26 

 

b.

 

Wire up a temporary connector for DC power.  Cut the +12V wire to 12 inches / 32 mm, 
and the GND wire to 24 inches / 64mm (reasons will become clear later).  Terminate to 
the two-way, .156 wire housing (as indicated on PCB), and solder the barrel connector (as 
shown below), for the external AC adaptor to the DC-DC converter.  This jumper will be 
partially disassembled later, to put the  AC power switch in line.  For now, just wire  it 
straight to the connector without the switch.   

 

Figure 8 - Barrel connector for Power Entry 

c.

 

If you are adding a gate booster, build a power jumper for it, using .1 x 3 wire housings.  
Whether  this  connector  is  straight  through  or  flips  depends  on  how  you  installed  the 
locking header in the EG section.  Refer to the section on installing the Gate Booster for 
more information.   

d.

 

If you intend to custom wire your reverb jumper using RG174 coax and the basic plugs, 
do that now.  You may also use a standard duplex RCA audio cable.  RG174 offers better 
noise shielding than the standard cable, and allows for the shortest possible run from the 
return plug on the reverb unit.  The return line carries a very weak signal and thus is the 
primary  source  of  noise  in  the  reverb  section.    Minimizing  the  length  and  optimized 
placement can dramatically improve the noise rejection.  Information on terminating the 
coax to the plugs is included in back of this manual.   

3.

 

Install sub boards (4027-1, VCF core 

–

 start with the 4012, and DC-DC converter.  Only fasten down 

the DC-DC converter.  If you are installing a gate booster, complete that installation now.  Details 
are included in the back of this guide.  

4.

 

Connect the DC-DC converter board input to the barrel connector assembly, but do not install the 
five-way jumper connecting its output to the main board.   

5.

 

Power-up checks: 

a.

 

Before applying power, and before connecting the DC-DC converter board to the main 
board, using the DMM in resistance mode, check the main board for shorts across the 
power rails.  Test at the five-way .156 locking header.  Take the readings as indicated on 
the  table  and  record  the  resistance  measured.    You  should  not  see  less  than  a  few 
hundred ohms and some will have much more.  If you see any reading of a few ohms or 
less, you have a short that must be identified and corrected before proceeding.  The most 
likely cause will be a solder bridge somewhere.  It may also be a reversed diode.  In either 
case, you should be able to find it through inspection.   

Summary of Contents for FuzzBass TTSH





















































Reviews:

No comments