26
Module Selection
Single press left right selection button, to choose FX module: Modul1-Modul2-Delay1-Delay2-Reverb
1-Reverb2-GEQ1-GEQ2)
Type
Single press dropdown button, then choose a wanted type from the dropdown listOne Echo 1/4 Two
Echo 1/8 Three Echo 1/16 Three Echo 1/16 Delayed Four Echo 1/16 One Echo 1/4 with 4 Reflect.
Dry-Wet
Ranges from 0 to 100 with a default @ 0. Adjust the parameter of Dry-Wet by dragging the slider, or
turning the main Encoder on the control panel.
EQ LS
Curve chart:
displays the LS curve
Gain
ranges is
±
18 dB, with a default @ 0 dB. Adjust the Gain by turning the main Encoder or on the
touch screen (fine tuning can be activated by pressing the main Encoder knob). Double press the
parameter frame to set it as default.
Freq
ranges from 20 Hz to 200 Hz, with a default @ 100 Hz. Adjust the Frequency by turning the main
Encoder or on the touch screen (fine tuning can be activated by pressing the main Encoder knob).
Double press the parameter frame to set it as default.
EQ HS
Curve chart:
displays the HS curve
Gain
ranges is
±1
8 dB, with a default @ 0 dB. Adjust the Gain by turning the main Encoder or on the
touch screen (fine tuning can be activated by pressing the main Encoder knob). Double press the
parameter frame to set it as default.
Freq
ranges from 1.5 KHz to 15 KHz, with a default @ 6.3 KHz. Adjust the Frequency by turning the
main Encoder or on the touch screen (fine tuning can be activated by pressing the main Encoder knob).
Double press the parameter frame to set it as default.
Other parameters
Factor
ranges from 0 to 13, with a default @ 1. Adjust the Factor by dragging the slider, or turning the
main Encoder on the control panel. (fine tuning can be activated by pressing the main Encoder knob).
Tempo
ranges from 40 to 240 BPM, with a default @ 80. Adjust the Tempo by turning the main Encoder
(fine tuning can be activated by pressing the main Encoder knob).
Tap Tempo:
Keep pressing this button to set BPM value, at least three times of pressing.
Delay Time:
ranges from 0 to 2000 ms, with a default @ 750ms. Adjust the time parameter by turning
the main Encoder or on the touch screen (fine tuning can be activated by pressing the main Encoder
knob).Double press the parameter frame to set it as default.
Delay Time can be configured by Factor and Tempo (see Chart 1 for the relation). Factor corresponds
to regular tuning, while Tempo corresponds to fine tuning. For example, set Factor to 8, Tempo to 120
BPM, Delay Time is 500 ms 60*1000/120=500 . if set Factor to 9, Delay Time will be 1000 ms. if Factor
to 7, Delay Time will be 250 ms.
13
2
3
4
5
6
Output Stage Sub-page
The sub-page mainly contains PAN, Solo, Mute, fader control and signal level display
Swtich Channel
Single press the key to switch between previous or next channel on the same layer
PAN control
The default is set as 50|50, the PAN value can be tuned by touch knob, or physical knob on the control panel.
Double press the parameter frame to set it back to default.
Solo
Single press the key to enable monitor, press again to disable it. The default is set as disabled.
Mute
Single press the key to enable mute, press again to disable it. The default is set as disabled
Fader control
Control the volume of fader level by dragging the slider, or faders on the control panel, the parameter frame
real-timely displays the value of fader level. Double press the parameter frame to fast set it back to 0.
Meter level display
The level meter of channel signal, indicating post-fader signal level of the channel.
