Library
Save or load user's EQ settings. Single press the dropdown button and select a library file from a popped-up
list, in order to load the EQ setting. Single press the
“S
ave
”
button after you have done with EQ settings,
then select the library file (there are 16 names of library, Preset 1~Preset16) from the popped-up list. You
could simply edit the name of library with a popped-up keyboard and press
“
confirm
”
or
“c
ancel
”
to save it
or not.
10
2
3
5
4
6
Dynamics sub-page
The sub-page includes channel selection, library, Gate, Compressor, Side Chain, etc.
Switch Channels
Single press the key to switch between previous or next channel on the same layer
Side chain
press dropdown button, and select Side chain channel (CH1~CH12 ) in the list (CH1~CH12 ST1 ST2)
.
Side Chain can select Pre/Post Eq of other single channel.
Gate
IN
: Single press the key to enable Gate, press again to disable it. The default is set as disabled.
Gate curve:
Y-axis indicates the Threshold, X-axis indicates time factor. Up curve is determined by Attack,
horizontal curve is determined by Hold, down curve is determined by Release.
Parameter Adjustment
: To adjust the parameter of Gate by dragging the slider, or turning the main Encoder
on the control panel (fine tuning can be activated when pressed the knob down). Double press the parameter
frame to set it as default.
Threshold
: Adjust the threshold of noise gate on the channel, ranges from -80 dB to 0 dB with default @ -80dB.
Any signal lower than Threshold will be cut off, as a result, the level of the signal has to surpass the threshold
in order to get through the noise gate.
Hold
(time of hold): from 2 ms up to 2000 ms with default @ 2 ms.
Attack
(time of start): from 0.5 ms to 100 ms with default @ 3 ms.
Release
(time of release): from 2 ms to 2 s with default @350 ms (compatible with many kinds of sound source)
Depth
: adjust attenuation of signals lower than the Threshold, ranges from 0 dB to -80 dB with default @-80 dB
29
2
3
4
5
GEQ Subpage
Double press
“
GEQ 1 or 2
”
in the FX Subpage, access to Subpage of GEQ parameter tuning, as showed in
the picture below
Module Selection
Single press left right selection button, to choose FX module: Modul1-Modul2-Delay1-Delay2-Reverb
1-Reverb2-GEQ1-GEQ2
Library
Save or load user's EQ settings. Single press the dropdown button and select a library file from a popped-up
list, in order to load the EQ setting. Single press the
“
Save
”
button after you have done with EQ settings,
then select the library file (there are 16 names of library, Preset 1~Preset16) which can be edited through
the soft-keyboard popping up. At last, press
“c
onfirm
”
or
“c
ancel
”
to save file name or not.
GEQ Chart
The right side shows the Gain coor18 0 -18 dB), The up side shows the Frequency coordinate
(20Hz 50Hz 100Hz 180Hz 300Hz 450Hz 620Hz 850Hz 1KHz 1.5KHz 3KHz 5.6KHz 9KHz 14KHz 20K Hz
the freq. to be determined) and gain value (default@0dB)of corresponding frequency point.
Drag the slider up and down to adjust gain of frequency point, or use corresponding physical faders to do it.
Operation
Bypass
: Single press the button, to enable Bypass. Press again to disable it. The default is disabled.
Flat
: Single press the button, to set all gains of frequency points back to 0, bring slider in the middle
(faders will be in the middle position of stroke if they are used to control), The default is disabled.
Fader selection button1-8
Single press the button, to control the gains of frequency points with 8 faders on the panel.
9-15
Single press the button, to control the gains of frequency points with 7 faders on the panel.
